Posts Tagged ‘siding’

Barnboard Siding Installation

September 4th, 2010 by KTU | 4 Comments | Filed in 5. Exterior Materials and Finishes, Park City Mountain Modern

Jose and gang started installing barnboard siding this week. It looks excellent. The barnwood comes from Trestlewood. They provided edged wood in random lengths and in widths of 4″, 6″, 8″, and 10″. By taking shorter lengths and a fair bit of narrow material, the material ended up costing just a bit more than virgin cedar siding. (A consistent irony of building green, is that reclaimed materials usually cost more than those cut fresh from the forest.) My cost for the barnwood ended up being about $3/sq-ft delivered, while #3 cedar siding currently costs about $2/SF, but usually requires staining, which would probably be another $1/SF. (You could leave the cedar to weather naturally, though, in which case it would be cheaper.) Incidentally, bids for the installation labor for this kind of board-to-board barnwood in Park City came in pretty consistently around $2.75-$3.00/SF including the labor to apply the Tyvek. This is probably on the low side because I have no window trim to install, although there are some fussy blocking details between the rafter tails.

Jorge nailing up barnwood siding. This is "rough gray" from Trestlewood.

(more…)

Tags: , , , ,

Cedar Shakes and Woodpeckers

September 5th, 2010 by KTU | No Comments | Filed in 2. Construction, Montana Sleeping Pavilion

On the main cabin we have had woodpecker problems over the years. Apparently the woodpeckers like to nest up high with a vantage point of the meadow. The gable end of the main cabin was perfect and they had made a mess of the tongue-and-groove cedar siding. We had patched with metal, but finally had to take drastic measures. My father-in-law had a guy apply galvanized steel sheet to the walls and then apply cedar shakes over that. This has mostly worked. Occasionally a wood pecker will attack, but after 1/2 inch of progress will give up. So on the pavilion, we’re taking the galvanized-plus-shakes approach from the get go.

Galvanized sheet steel then cedar shakes...woodpecker proof.

Tags: , , , ,

Steel Siding

September 17th, 2010 by KTU | 17 Comments | Filed in 5. Exterior Materials and Finishes, Park City Mountain Modern

The roofers have nearly completed the steel siding on the house. I’m very happy with the results. We are using 2′ x 3′ 20 gauge cold-rolled steel flat panels. It is very inexpensive (~$2/sq-ft materials and labor), and I think it looks fantastic. It will rust to a reddish brown when exposed the weather for a few months.

The cold-rolled steel panels run in an 8 ft. high band around the house. This is kind of a poor-man's Frank Gehry panel system. (He uses complex metal panel configurations on many of his buildings.)

(more…)

Tags: , , , , , , ,

Accelerating Oxidation of Steel Siding Panels

May 8th, 2011 by KTU | 18 Comments | Filed in 5. Exterior Materials and Finishes, Park City Mountain Modern

The cold-rolled steel roof has oxidized nicely over the fall and winter. It looks pretty good. Most of the steel siding is starting to turn as well, but it is pretty well protected from water, and with temperatures mostly below 50F, the oxidation rate is slow. Still, I’m pretty sure that by the end of the summer, most of the steel siding will have a decent patina on it.

However, the steel panels on the front of the house are very well protected. They basically never get wet. By mid-Spring they were looking pristine. So, I decided I would accelerate the process. Here is the siding in that area before I did anything…

Steel siding on front of house. Because it is protected by the awning, only the very bottom had oxidized at all after a winter and spring.

(more…)

Tags: , , , , , , ,